H&R AUDI A6 C6 TYPE 4F 2WD + 4WD 2004> Sport Spring
SKU: 29200-2
Vehicle Make: Audi
RM1,880
Shipping & returns
Dispatch time is confirmed via WhatsApp.
Compatibility
- AUDI · A6 C6
Key Features
- Sporty look & performance: H&R lowering springs are the ideal solution for anyone who wants to optimize the handling of their car and achieve a sporty look while retaining the standard ride comfort, through the exact set-up of the springs to the original shock absorbers.
- Developed & manufactured in Germany, with ABE (only valid in Germany) or part approval.
- Discreet lowering of the vehicle's centre of gravity in conjunction with the standard suspension.
- Vehicle variants with electronically controlled shock absorbers or so-called active suspensions keep their functions fully intact.
- Made of hardened and tempered spring steel with weather-resistant surface protection by zinc phosphating & powder coating, mostly in the colour "H&R Blue".
- 100% Made in Germany – 100% Made in the Sauerland, manufactured at the H&R headquarters in Lennestadt.
- Quality management system certified according to ISO 9001:2015, fulfilling the approval-relevant requirements of the Federal Motor Transport Authority (KBA) for type/part approvals under German road traffic law.
Specifications
| Lowering (official) | Lowering of the body up to about 40 mm *) (depending on the vehicle type and version) by using different springs. *) S6: 25/15 mm (axle 1/axle 2) |
| Spring type | Stahl-Schraubendruckfedern (steel coil springs) |
| Corrosion protection | Powder coating (Kunststoffbeschichtung) |
| Coil markings | `29200-1 VA (F)` · `29200-2 VA (F)` · `29200 HA (R)` |
| Approval documentation | Teilegutachten 42TG0341E-04, 2006-09-27; basis: VdTÜV-Merkblatt Nr. 751 |
| Application range (as printed) | EC type approval No. Audi [0588] 4F Audi A6 / -Quattro / -S6 (Limousine / Sedan, Avant / Station wagon) (2WD, 4WD) 1350 / 1260 (Limousine) 1350 / 1335 (Avant) e1*2001/116*0254 * . . |
| Permissible axle loads, front/rear | 1350 / 1260 kg; 1350 / 1335 kg |
| Official note | Vehicles with level control shall not be retrofitted in the way described above. |
| Official test result | "no negative effects on the operational safety and roadworthiness of the vehicle were noticed. The methods applied make certain that the accuracy of measurement of the quantitative test results satis- fies the requirements of the bases of testing listed in V" |
Installation
Professional installation is recommended for this product.
Book an AppointmentInstallation and usage guidance is general reference only. Manufacturer instructions take precedence. Visitors uncertain about installation or use should seek professional advice.
FAQ
What is the official lowering of this H&R Sport Spring?
Per the Teilegutachten 42TG0341E-04: Lowering of the body up to about 40 mm *) (depending on the vehicle type and version) by using different springs. *) S6: 25/15 mm (axle 1/axle 2)
Source: official_technical_document · 2026-09-02
What approval documentation does this spring carry?
Teilegutachten (Nr. 42TG0341E-04), dated 2006-09-27, issued under StVZO §19(3) Nr. 4 — the standard German acceptance-of-modification (Änderungsabnahme) process applies after installation.
Source: official_technical_document · 2026-09-02
What must be checked after installation?
Per the Teilegutachten: headlamp setting is to be checked; suspension alignment is to be taken after the vehicle is retrofitted; on vehicles with a load-dependent brake pressure controller, this is to be reset to the unladen level (per manufacturer instructions).
Source: official_technical_document · 2026-09-02