H&R HONDA 2008-2015 Sport Spring
SKU: 29023-1
Vehicle Make: Honda
RM1,580
Shipping & returns
Dispatch time is confirmed via WhatsApp.
Compatibility
- HONDA · ACCORD
Key Features
- Sporty look & performance: H&R lowering springs are the ideal solution for anyone who wants to optimize the handling of their car and achieve a sporty look while retaining the standard ride comfort, through the exact set-up of the springs to the original shock absorbers.
- Developed & manufactured in Germany, with ABE (only valid in Germany) or part approval.
- Discreet lowering of the vehicle's centre of gravity in conjunction with the standard suspension.
- Vehicle variants with electronically controlled shock absorbers or so-called active suspensions keep their functions fully intact.
- Made of hardened and tempered spring steel with weather-resistant surface protection by zinc phosphating & powder coating, mostly in the colour "H&R Blue".
- 100% Made in Germany – 100% Made in the Sauerland, manufactured at the H&R headquarters in Lennestadt.
- Quality management system certified according to ISO 9001:2015, fulfilling the approval-relevant requirements of the Federal Motor Transport Authority (KBA) for type/part approvals under German road traffic law.
Specifications
| Lowering (official) | Lowering of the body up to about 35 mm (depending on the vehicle type and version) by using different springs. |
| Spring type | Stahl-Schraubendruckfedern (steel coil springs) |
| Wire diameter (axle 1-I / axle 1-II / axle 2-I / axle 2-II) | 13.5 mm / 13.5 mm / 11.0 mm / 11.0 mm |
| Total number of coils (axle 1-I / axle 1-II / axle 2-I / axle 2-II) | 6.7 / 6.7 / 10.5 / 10.5 |
| Untensioned length (axle 1-I / axle 1-II / axle 2-I / axle 2-II) | 280 mm / 290 mm / 345 mm / 360 mm |
| Corrosion protection | Powder coating (Kunststoffbeschichtung) |
| Bump stop, spring travel (max.) | Standard |
| Coil markings | `H&R 29023 VA (F)` · `H&R 29023 HA (R)` |
| Approval documentation | Teilegutachten 82XT0148-02, 2010-04-01; basis: VdTÜV-Merkblatt Nr. 751 |
| Application range (as printed) | Honda Motor (J) [7100] CU1 , CU2, CU3 CW1, CW2, CW3 Accord (Limousine/Sedan) Accord Tourer 1200 / 950 1200 / 1030 e6*2001/116*0113 // 0114 // 0115* . . e6*2001/116*0120 // 0121 // 0122* . . |
| Permissible axle loads, front/rear | 1200 / 950 kg; 1200 / 1030 kg |
| Official note | Vehicles with level control shall not be retrofitted in the way described above. |
| Official test result | "no negative effects on the operational safety and roadworthiness of the vehicle were noticed. The methods applied make certain that the accuracy of measurement of the quantitative test results satis- fies the requirements of the bases of testing listed in V" |
Installation
Professional installation is recommended for this product.
Book an AppointmentInstallation and usage guidance is general reference only. Manufacturer instructions take precedence. Visitors uncertain about installation or use should seek professional advice.
FAQ
What is the official lowering of this H&R Sport Spring?
Per the Teilegutachten 82XT0148-02: Lowering of the body up to about 35 mm (depending on the vehicle type and version) by using different springs.
Source: official_technical_document · 2026-09-02
What approval documentation does this spring carry?
Teilegutachten (Nr. 82XT0148-02), dated 2010-04-01, issued under StVZO §19(3) Nr. 4 — the standard German acceptance-of-modification (Änderungsabnahme) process applies after installation.
Source: official_technical_document · 2026-09-02
What must be checked after installation?
Per the Teilegutachten: headlamp setting is to be checked; suspension alignment is to be taken after the vehicle is retrofitted; on vehicles with a load-dependent brake pressure controller, this is to be reset to the unladen level (per manufacturer instructions).
Source: official_technical_document · 2026-09-02