H&R MASERATI 2013> Sport Spring
SKU: 28801-1
Vehicle Make: Maserati
RM2,270
Shipping & returns
Dispatch time is confirmed via WhatsApp.
Compatibility
- MASERATI · GHIBLI
Key Features
- Sporty look & performance: H&R lowering springs are the ideal solution for anyone who wants to optimize the handling of their car and achieve a sporty look while retaining the standard ride comfort, through the exact set-up of the springs to the original shock absorbers.
- Developed & manufactured in Germany, with ABE (only valid in Germany) or part approval.
- Discreet lowering of the vehicle's centre of gravity in conjunction with the standard suspension.
- Vehicle variants with electronically controlled shock absorbers or so-called active suspensions keep their functions fully intact.
- Made of hardened and tempered spring steel with weather-resistant surface protection by zinc phosphating & powder coating, mostly in the colour "H&R Blue".
- 100% Made in Germany – 100% Made in the Sauerland, manufactured at the H&R headquarters in Lennestadt.
- Quality management system certified according to ISO 9001:2015, fulfilling the approval-relevant requirements of the Federal Motor Transport Authority (KBA) for type/part approvals under German road traffic law.
Specifications
| Lowering (official) | Lowering of the body up to about 35 mm *) (depending on the vehicle version) by using special springs. *) Ghibli Trofeo nur bis zu ca. 20 mm an Achse 2 / Ghibli Trofeo only up to about 20 mm at axle 2 |
| Spring type | Stahl-Schraubendruckfedern (steel coil springs) |
| Wire diameter (axle 1-I / axle 1-II / axle 2-I / axle 2-II) | 15.5 mm / 15.5 mm / 15.5 mm / 15.5 mm |
| Total number of coils (axle 1-I / axle 1-II / axle 2-I / axle 2-II) | 6.95 / 7.0 / 8.7 / 8.7 |
| Untensioned length (axle 1-I / axle 1-II / axle 2-I / axle 2-II) | 293 mm / 302 mm / 317 mm / 335 mm |
| External diameter (axle 1-I / axle 1-II / axle 2-I / axle 2-II) | 121 mm / 122 mm / 108 mm / 110 mm |
| Corrosion protection | Powder coating (Kunststoffbeschichtung) |
| Bump stop, spring travel (max.) | Standard |
| Coil markings | `28801 VA (F)` · `H&R 28801 HA (R)` · `28801-2 VA (F)` · `H&R 28801-2 HA (R)` · `Federn 28801-2 VA (F)` · `springs 28801-2 VA (F)` |
| Approval documentation | Teilegutachten 142XT0142-02, 08.06.2022; basis: VdTÜV-Merkblatt Fahrzeug und Mobilität 751 |
| Application range (as printed) | Maserati (I) 4014 M156 Ghibli, Ghibli S, Ghibli Diesel, Ghibli Trofeo (2WD) 1200 / 1340 e3*2007/46*0224* . . +) in Bezug auf die Richtlinie 2007/46/EG, zuletzt geändert durch die Verordnung (EU) 2018/858 with regard to Directive 2007/46/EC, as last amended by Regulation (EU) 2018/858 F) s. IV.3.3 |
| Permissible axle loads, front/rear | 1200 / 1340 kg |
| Official test result | "no negative effects on the operational safety and roadworthiness of the vehicle were noticed." |
Installation
Professional installation is recommended for this product.
Book an AppointmentInstallation and usage guidance is general reference only. Manufacturer instructions take precedence. Visitors uncertain about installation or use should seek professional advice.
FAQ
What is the official lowering of this H&R Sport Spring?
Per the Teilegutachten 142XT0142-02: Lowering of the body up to about 35 mm *) (depending on the vehicle version) by using special springs. *) Ghibli Trofeo nur bis zu ca. 20 mm an Achse 2 / Ghibli Trofeo only up to about 20 mm at axle 2
Source: official_technical_document · 2026-09-02
What approval documentation does this spring carry?
Teilegutachten (Nr. 142XT0142-02), dated 08.06.2022, issued under StVZO §19(3) Nr. 4 — the standard German acceptance-of-modification (Änderungsabnahme) process applies after installation.
Source: official_technical_document · 2026-09-02
What must be checked after installation?
Per the Teilegutachten: headlamp setting is to be checked; on vehicles with a load-dependent brake pressure controller, this is to be reset to the unladen level (per manufacturer instructions).
Source: official_technical_document · 2026-09-02